Arduinoホーム気象ステーション

• 対角表示-1.8インチ、解像度128x160ピクセル、18ビットカラー（262,144色）
• ピクセルメモリアドレッシングが統合されたコントローラー
• 内蔵microSDスロット-2本以上のデジタルラインを使用
• 3.3および5Vに対応
• 寸法：34 mm x 56 mm x 6.5 m

#include <Wire.h> // library for communication with I2C devices #include <Adafruit_Sensor.h> // Core library for all sensors #include <Adafruit_BMP085_U.h> // library for BMP180 #include <Adafruit_GFX.h> // Core graphics library #include <Adafruit_ST7735.h> // Hardware-specific library #include <SPI.h> // library for communication with SPI devices #include "dht.h" // library for DHT #define DHT22_PIN 2 // connect data pin of DHT22 to 2 digital pin #define TFT_CS 10 // connect CS pin of TFT to 10 digital pin #define TFT_RST 9 // connect RST pin of TFT to 9 digital pin // you can also connect this to the Arduino reset // in which case, set this #define pin to 0! #define TFT_DC 8 // connect DC pin of TFT to 8 digital pin Adafruit_ST7735 tft = Adafruit_ST7735(TFT_CS, TFT_DC, TFT_RST); //initialize TFT #define TFT_SCLK 13 // connect SCLK pin of TFT to 13 digital pin #define TFT_MOSI 11 // connect MOSI pin of TFT to 11 digital pin dht DHT; Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085); //initialize BMP180 int bmpFlag = 0; struct { uint32_t total; uint32_t ok; uint32_t crc_error; uint32_t time_out; uint32_t connect; uint32_t ack_l; uint32_t ack_h; uint32_t unknown; } stat = { 0,0,0,0,0,0,0,0}; // struct for dht status void setup(void) { Serial.begin(9600); Serial.println("Meteo Test"); Serial.println(""); if(!bmp.begin()) // check connection for BMP180 { Serial.print("Ooops, no BMP180 detected ... Check your wiring or I2C ADDR!"); bmpFlag = 1; } tft.initR(INITR_BLACKTAB); // Initialize TFT and fill with black color tft.fillScreen(ST7735_BLACK); tft.setRotation(tft.getRotation() + 1); tft.setTextSize(1.5); delay(500); // delay in order to ensure that TFT was initialized } // last measured data float oldTemperature = 0, oldAltitude = 0, oldPressure = 0, oldDHTHumidity = 0, oldDHTTemperature; bool wasUpdate = false; void loop(void) { if(Serial.available() > 0) // we have data is Serial port { Serial.read(); // read byte from serial port and send last measured data printValue("Pressure", oldPressure, " hPa", false); printValue("Temperature", oldTemperature, " C", false); printValue("Altitude", oldAltitude, " m", false); printValue("Humidity", oldDHTHumidity, "%", false); printValue("DHT_temperature", oldDHTTemperature, " C", false); Serial.println("END_TRANSMISSION"); } sensors_event_t event; float temperature, altitude; if(bmpFlag == 0){ bmp.getEvent(&event); // get data from BMP180 if (event.pressure) { bmp.getTemperature(&temperature); float seaLevelPressure = SENSORS_PRESSURE_SEALEVELHPA; altitude = bmp.pressureToAltitude(seaLevelPressure, event.pressure, temperature); } else { Serial.println("Sensor error"); } } uint32_t start = micros(); int chk = DHT.read22(DHT22_PIN);// get data from DHT22 uint32_t stop = micros(); stat.total++; switch (chk) // check status of DHT22 { case DHTLIB_OK: stat.ok++; break; case DHTLIB_ERROR_CHECKSUM: stat.crc_error++; Serial.print("Checksum error,\t"); break; case DHTLIB_ERROR_TIMEOUT: stat.time_out++; Serial.print("Time out error,\t"); break; case DHTLIB_ERROR_CONNECT: stat.connect++; Serial.print("Connect error,\t"); break; case DHTLIB_ERROR_ACK_L: stat.ack_l++; Serial.print("Ack Low error,\t"); break; case DHTLIB_ERROR_ACK_H: stat.ack_h++; Serial.print("Ack High error,\t"); break; default: stat.unknown++; Serial.print("Unknown error,\t"); break; } if(bmpFlag != 0 || !event.pressure) // update data { tft.fillRect(0, 30, 160, 6, ST7735_BLACK); tft.setCursor(0, 30); tft.setTextColor(ST7735_RED); printValue("ERROR BMP INITIALIZATION", 0, "", true); } else { if(event.pressure != oldPressure) { tft.fillRect(0, 30, 160, 7, ST7735_BLACK); tft.setCursor(0, 30); tft.setTextColor(ST7735_RED); printValue("Pressure", event.pressure, " hPa", true); oldPressure = event.pressure; wasUpdate = true; } if(temperature != oldTemperature) { tft.fillRect(0, 38, 160, 7, ST7735_BLACK); tft.setCursor(0, 38); tft.setTextColor(ST7735_WHITE); printValue("Temperature", temperature, " C", true); oldTemperature = temperature; wasUpdate = true; } if(altitude != oldAltitude) { tft.fillRect(0, 46, 160, 7, ST7735_BLACK); tft.setCursor(0, 46); tft.setTextColor(ST7735_BLUE); printValue("Altitude", altitude, " m", true); oldAltitude = altitude; wasUpdate = true; } } if(DHT.humidity != oldDHTHumidity) { tft.fillRect(0, 54, 160, 7, ST7735_BLACK); tft.setCursor(0, 54); tft.setTextColor(ST7735_GREEN); printValue("Humidity", DHT.humidity, "%", true); oldDHTHumidity = DHT.humidity; wasUpdate = true; } if(DHT.temperature != oldDHTTemperature) { tft.fillRect(0, 80, 160, 7, ST7735_BLACK); tft.setCursor(0, 80); tft.setTextColor(ST7735_YELLOW); printValue("DHT_temperature", DHT.temperature, " C", true); oldDHTTemperature = DHT.temperature; wasUpdate = true; } if(wasUpdate) { Serial.println("END_TRANSMISSION"); } wasUpdate = false; delay(10000); } void printValue(char* title, double value, char* measure, bool tftPrint) { if(tftPrint) // print data to TFT { tft.print(title); tft.print(": "); tft.print(value); tft.println(measure); } Serial.print(title); // send data to Serial port Serial.print(": "); Serial.print(value); Serial.println(measure); }